Customer Reviews

4.95 out of 5
Write a Review
  • All Reviews (183)
  • Image (25)
  • Video (2)
  • All Star
    • All Star(183)
    • 5 Star(176)
    • 4 Star(5)
    • 3 Star(1)
    • 2 Star(1)
    • 1 Star(0)
Sort by:
Top Review
  • Top Review
  • Most Helpful
  • Most Recent
Reviews only from your country (United States)
  • July-21 2017 04:26:17

    Frequency measurement: I managed to run it only if the input signal is between 4.7 and 5 volts (not to be exceeded). The signal goes directly to pin 3 of the PIC (5V max). An incoming signal amplification circuit must be provided. Quartz measurements: Very poor circuit. It depends a lot on the supply voltage, the temperature and the quartz frequency. Limited use. Measurement examples: (3,2748 MHz -> 0) (4,9152 MHz -> 4,9166) (16 MHz -> 16,001 16,006) (20 MHz -> 20,007) (22 MHz ->

  • May-19 2019 07:44:02

    High Quality DIY Frequency Counter and Crystal checker. Works perfect !! Testing a 8700.000Hz crystal and a 50Hz input signal. See Pictures. Recommended !!!!

    November-08 2018 21:23:29

    Thank YOU Please I did pay in September the RK560 frequency counter meter . Take pictures Photos the Bill Ticket that It did pay in date September 2018. I will wait the RK560 Frequency Counter Meter . Please read see pictures Photos the Bill Ticket. Thank YOU BANGGOOD very very much BANGGOOD.

  • January-26 2016 16:31:45

    Ještě jsem jej nezkoumal. Tak nevím jak je to se vstupními obvody. Celé je to postaveno na procesoru PIC. Myslel jsem, že tam bude ATMega. Nevadí. Jinak standardní PCB, i ostatní součástky. Doufám tedy že bude sloužit dobře

  • August-11 2016 14:51:16

    Quick project for the beginning kit builder. I would suggest Chuck Adams (K7QO) website for step by step English build instructions - look for "Kit Exercise #1 Chinese Crystal Checker and Frequency Counter". When built kit is a very useful Crystal tester. I would like to have instructions on some of the other features that are selected by the push button. Also I wondered if in needs calibration since all crystals checked are 0.3-0.5 kHz above the stamped valu

  • March-02 2017 14:56:32

    Dear Sir, I have receive the meter but when I turn on, one bar led of the display is off. All of the d (led bar) are of . So it is imposible to read any number. Please What I have to do? thank you

    Comments (1)
  • May-14 2017 00:10:27

    Kit was simple as usual to construct. Some Instructions would be nice. Here you see it's working with 16M Crystal for Arduino . Next Counter using M8 Transistor Tester(Ver.12864) 25Khz test signal. I'm Happy. You Happy ?

  • April-01 2018 18:20:31

    Funziona benissimo e con qualche modifica si può migliorare ancora di più

  • September-25 2017 12:35:44

    Work very nice .Very good product and delivery service

  • September-04 2017 02:39:05

    Perfect to read frequency.. For the the price I pay I am very satisfied...


    Total 0 pages

    Go to page


    You might be interested in

    recommendation for you
    • US$5.99
    • US$4.99
    • US$4.93
    • US$9.99
    • US$33.99
    • US$9.99
    • US$3.99
    • US$4.99
    • US$7.99
    • US$3.99
    • US$22.98
    • US$5.99
    • US$11.99
    • US$1.99
    • US$14.19
    • US$37.99
    • US$17.38
    • US$16.99