EricF
Q: How do I set Waypoints? I can't see it in the instruction guide. Thanks
Asked by MatBat on 2019-10-23 01:47:30
Q: 4 servos are indicated. Does that mean it has ailerons in addition to the rudder-elevator servos?
Asked by greatbang on 2019-08-04 05:43:24
EricF Yes, it has ailerons, and V tail, so 4 servos are required.
2019-08-22 05:22:06 Helpful (4)Q: I just cant get it to work any one no how to connect correctly
Asked by Mart McFly on 2019-06-10 01:55:47
EricF Have you flashed the proper firmware to the SN L flight controller? it requires a special version to work with the AAT
2019-06-26 04:49:22 Helpful (1)
EricF Position data is sent over the video signal, integrated into the OSD info in some fashion I think. According to info in the manual. It only works with the SN L Owl FC to my knowledge. But it does say it supports Mavlink, so it should work with others. But you are on your own getting it to work with those other than reading their manual.
2019-06-26 04:48:32 Helpful (1)Q: What is needed in the aircraft for this to work?
Asked by DeanScholes on 2019-05-20 12:54:04
EricF You need the SN L Owl Flight Controller on the airplane
2019-06-26 04:47:40 Helpful (0)Q: Does this support both of 1.2G and 5.8G signal ?
Asked by kenchengrchobby on 2019-05-05 07:28:19
EricF It does not have a receiver, so it technically supports any frequency. However it is designed for 5.8 antennas due to its size.
2019-06-26 04:46:58 Helpful (0)
Q: Any manual, software for programming... ? English language supported?
Asked by mazsola76bg6 on 2019-01-29 03:44:58
EricF Yes, there is an English manual, as well as English firmware here https://github.com/HelloLeFei/SN_L You can use any USB to Serial adapter such as an FTDI to flash the new firmware via the GPS port. Any Ublox compatible GPS module will work as well. I have tested with BN220 and BN880 and both work well. You do not need the power module to use this. You can supply the 5v power via any 5v regulator
2019-02-24 01:23:11 Helpful (0)Q: I wonder if it comes with all modules, GPS, current sensor and USB cable.
Asked by wilsonconsultor on 2019-01-30 08:53:26
EricF No. This listing only comes with the main board as pictured.
2019-02-24 01:18:19 Helpful (0)
EricF Any M8N GPS module should work. GPS modules are very standardized. If the FC does not send auto config messages to the module, at most you will need to connect it to a PC with Ucenter and set the parameters appropriately. Not difficult. The USb updater is simply a USB to TLL Serial adapter. Any will work simply connecting to the appropriate pins on the GPS connector, and finding the appropriate baud rate. The power module is nothing more than a few regulators, and a current sensor and voltage sensor. Others should work. Only a few fairly universal current sensor types are used in the FC market. One of the Matek FCHUB's with current sensor may even work without modification. If not, only a few minor modifications to the voltage and current sensor will be required.
2019-02-22 02:26:00 Helpful (0)Q: Wich GPS module will work with the controller?
Asked by Volker on 2019-01-30 06:44:22
EricF Any M8N GPS module should work. GPS modules are very standardized. If the FC does not send auto config messages to the module, at most you will need to connect it to a PC with Ucenter and set the parameters appropriately. Not difficult.
2019-02-22 02:22:04 Helpful (0)We sincerely invite you to subscribe to the Invite Answer email!
If you subscribe, we will invite you via email to answer questions people have about products. By subscribing you]ll also earn the "Helpful Badge"! You can unsubscribe at any time on the privacy settings page.
Help others and be happier!
Thank you for subscribing! You have also earned a badge!
Thank you! Your answer will help ###name### and ###num### other people!
Check awaiting answers to see more people who need help.
Thank you! Your answer will help ###name### and ###num### other people!
Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!
We invite you to subscribe to our Invite Answer email!
Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.
EricF Use MissionPlanner or QgroundControl from the Ardupilot project. It works with NAVI as it fully supports the mavlink protocol.
2019-11-02 01:46:32 Helpful (2)