louisvr45
Q: how can you program/flash them with the simonk's firmware to use them with multirotors?
Asked by louisvr45 on 2018-08-12 02:36:20
Q: wiill it work with flsky gt3 tx?
Asked by louisvr45 on 2021-01-28 05:01:14
Ken Fawn Yes
2022-04-29 12:04:43 Helpful (0)Q: what is inside diameter of this hub? and is nuts supplied with it?
Asked by louisvr45 on 2022-03-26 06:28:38
The seller no data.
2022-03-30 06:00:31 Helpful (0)Q: is this module compatible with futaba ff7, 9chp radio that takes a module?
Asked by louisvr45 on 2021-12-08 01:55:00
Thorsam if you use ppm mode,it can compatible,but i do not recommend
2021-12-09 03:05:14 Helpful (0)Q: is this rx compatible with futaba 14sg
Asked by louisvr45 on 2021-06-16 05:19:50
louisvr45 you could always solder the esc and motor wires directly without connecrors.. then you have better connectivity
Q: does this rx support futaba fhss egbfutaba 14sg?
Asked by louisvr45 on 2021-01-02 10:45:40
dengjunbao no
2021-01-07 12:09:52 Helpful (0)
Donald Maybe BG could answer the question here, rather than sending us off to Customer Non-Service with that ridiculous answer to ask the BG customer service team. Answer the question BG. Stop passing it off to another non-service team.
2020-10-16 03:16:00 Helpful (0)
Q: can this flight controller be used for a flying wing?
Asked by louisvr45 on 2019-08-26 07:46:33
mric3412 Onlywith INAV (or betaflight, cleanflight etc.) but not for arduplane since it's a f411 microcontroller. You have 4 PWM out, so it's OK for an INAV flying wing with 2 elevons and one motors ( 1 spare PWM out for a second motor or yaw control for example)
2019-09-25 12:50:12 Helpful (0)Q: cw or ccw ?
Asked by larsHB on 2018-11-24 12:07:21
louisvr45 where can i find ccw m6 nuts?
2019-09-03 02:39:51 Helpful (0)Q: can this fc be used on a flying wing?
Asked by louisvr45 on 2019-08-25 02:11:54
Squinch no
2019-09-01 09:15:55 Helpful (0)
louisvr45 the heatsink also needs a fan .. on a 40mm heat sink it reach 70 degrees in 2 min
2019-05-17 04:19:11 Helpful (0)
We sincerely invite you to subscribe to the Invite Answer email!
If you subscribe, we will invite you via email to answer questions people have about products. By subscribing you]ll also earn the "Helpful Badge"! You can unsubscribe at any time on the privacy settings page.
Help others and be happier!
Thank you for subscribing! You have also earned a badge!
Thank you! Your answer will help ###name### and ###num### other people!
Check awaiting answers to see more people who need help.
Thank you! Your answer will help ###name### and ###num### other people!
Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!
We invite you to subscribe to our Invite Answer email!
Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.
.JPG)
vahoo with ftdi or arduino nano
2022-10-16 05:12:27 Helpful (0)