Customer Reviews

4.67 out of 5
Write a Review
  • All Reviews (12)
  • Image (0)
  • Video (0)
  • All Star
    • All Star(12)
    • 5 Star(9)
    • 4 Star(2)
    • 3 Star(1)
    • 2 Star(0)
    • 1 Star(0)
Sort by:
Top Review
  • Top Review
  • Most Helpful
  • Most Recent
Reviews only from your country (United States)
  • March-19 2015 23:50:23

    Hi I bought 2 sets of these and they came in due time. The problem is that the heatsinks are missing the special heat transfer adhesive and I can't use them. Why did this happen? Also one set was completely different that the other, especial the drivers. Is it possible for banggood to send me the heat transfer adhesive ASAP ?

    Comments
  • January-08 2015 10:10:33

    The ramps board was well packaged and works fine, but double check the Pololu drivers. All the heat sinks were touching the pins at one side and I have to remove them and and fixed them with a drop of superglue. The origin used therminal adhesive is not that strong and to remove the heat sinks was not a big deal.

    Comments
  • September-06 2014 07:48:49

    Product (as always with Banggood) arrived well within the stated delivery times and was well wrapped and protected which was lucky as the packet had obviously been dropped in the post as one of the corners was dented, but minimal damage (a couple of bent pins that were easily sorted) occurred. The stepper drivers were all well soldered and the heatsinks applied well without causing shorts across the pins (I've seen some poor quality ones on ebay that do!). Mine came adjusted almost perfectly but maybe

    Comments
  • March-17 2016 10:29:38

    I just recieved this ramps board, and im glad i didnt put it on my printer before inspection. This board has ALLOT of bad soldering points on the backside. Some pads with basicly no solder at all, and some where the solder didnt flow correctly. The card would have been great, if the QC had been better.

    Comments
  • March-20 2015 12:39:13

    Ho acquistato la RAMPS e i driver per una seconda stampante 3D ma rispetto ad un precedente acquisto la ramps ha l pin disallineati per cui è difficile l'inserimento nella scheda Arduino. Due driver non funzionano e i dissipatori a corredo non hanno l'adesivo per attaccarli al 4988 dei driver.

    Comments
  • February-06 2016 11:09:05

    Based on a Prusa I3, with some small modifications in pins.h and marlin.cpp Heatbeat mosfet is driving the laser now. Swapped D8 en D9 in the Marlin firmware. Heatbed mosfet is fan mosfet now. Modifing M106 and M107 to be M03 and M05. M03 PWM.

    Comments
  • December-15 2015 11:58:27

    It is as decribed, but sadly there was a fatal solder problem, but it was easily correctable.

    Comments
  • April-19 2016 03:23:48

    Assemble the ok. havent test them yet

    Comments
  • March-20 2016 08:22:09

    Elettronica perfetta

    Comments
  • March-17 2016 05:14:52

    Usefull to make a 2nd Reprap

    Comments
Show:

    Total 0 pages

    Go to page

    Go

    You might be interested in

    recommendation for you
    • US$10.99
    • US$39.33
    • US$4.23
    • US$2.99
    • US$7.95
    • US$14.99
    • US$3.68
    • US$15.79
    • US$19.99
    • US$8.42
    • US$259.00
    • US$196.00
    • US$299.00
    • US$21.48
    • US$209.00
    • US$399.00
    • US$34.99
    • US$7.79