Customer Reviews

4.78 out of 5
Write a Review
  • All Reviews (40)
  • Image (4)
  • Video (0)
  • All Star
    • All Star(40)
    • 5 Star(35)
    • 4 Star(3)
    • 3 Star(1)
    • 2 Star(0)
    • 1 Star(1)
Sort by:
Top Review
  • Top Review
  • Most Helpful
  • Most Recent
Reviews only from your country (United States)
  • February-21 2018 14:06:38

    Al extraerlo de su caja se aprecia que recibió un fuerte golpe durante el transporte, solo hay que ver como esta el precinto de garantía, lo he probado y funciona, pero tendré que intentar enderezar las chapas del chasis, aviso que tendré que romper el precinto de garantía. Ver las fotos.

    Comments
  • January-16 2018 06:51:05

    t's worth having gotten dented one of the right flaps at the location where the trim RV is. usually have arrived in conditions.

    Comments
  • August-26 2018 11:31:52

    - Correct quality - Works very well - Adjustable power supply from 16 to 28 VDC

    Comments
  • February-08 2017 00:34:23

    very good quality In the standard set to 220V. Connect the cables and lets go!

    Comments
  • July-06 2020 09:49:10

    se tardó más de lo que esperaba

    Comments
  • May-31 2020 14:04:40

    tip yop

    Comments
  • March-20 2020 07:55:11

    alimentation deja servie c est pas du materiel neuf etiquette de garentie arrachee !!!!

    Comments
  • March-05 2015 12:47:31

    Although without a fan, it does a good job to drive my CNC xPro controller and four steppers (3x NEMA 23 and 1x NEMA 17) along with a few bling. Pictures and video will follow once I clean up my setup. A few pictures already available at : http://www.openbuilds.com/builds/myox-a-4-x-2-ox-cnc-with-potential.915/

    Comments
  • June-22 2014 23:13:23

    I just received this 24V 10A SMPS and tested the output voltage with my digital multimeter which was 24V as described. I was kind of surprised to find that it does not have a fan inside which was rather unusual for an SMPS. Although it was described as an SMPS for LED lights, I intend to use it for supplying power for my CNC or 3D printer project. And even though I gave all 5 stars, I do not know yet how long this SMPS will last but it appears to be OK. I will update later if I find more.

    Comments
  • March-16 2013 02:28:07

    Very good power module. You can extend output voltage range (no load to full load) by changing R20 to 1.2kOm (low voltage limit ~9V) and VR1 to 4.7kOm (trimmer - high voltage limit ~33V). Under 8V not work stable and breakdown voltage of output capacitors is 35V !!!

    Comments
Show:

    Total 0 pages

    Go to page

    Go
    recommendation for you
    • US$3.17
    • US$8.90
    • US$4.23
    • US$6.36
    • US$7.99
    • US$17.99
    • US$15.16
    • US$3.50
    • US$3.99
    • US$29.97
    • US$7.99
    • US$13.99
    • US$22.99
    • US$9.99
    • US$15.49
    • US$11.99
    • US$19.99
    • US$26.51