AtilaKosegil i bought same. same problem.

Submit

Marekzenio Hej.Marek.Sprawdzaem oba wejcia w radiu na kamer a także video In w tej dużej wtyczce. To samo na obu wejciach. Kamerka wraz z przewodem sprawdzana pod zwykym telewizorem zasilana zasilaczem - dziaa.
I have got the same issue. Camera with wires works ok only after connecting to TV -( Video in signal) powered from the external power supply.
In the car with radio does not work !!! I tried with CCD IN and AUX Video IN in the radio. Also tried external power supply ....unsuccessfully.
It is time to write to Banggood...

Submit

UriCohen you need to set the reverse camera to sd under factory settings

Submit

UriCohen you need to set reversing cam to sd under factory settings

Submit

BG411516142 estou com mesmo problema

Submit

NPL Isee the same issue

Submit

Anna Liz tengo el mismo problema en mi estereo

Submit

NikosKam Same problem. Did you find out any solution?

Submit

Marekzenio Anyonehas got properly working camera? I have the same issue!

Submit

Marekzenio Anyonehasgot properly working camera? I have the same issue!

Submit

Marekzenio I have the same issue. Camera does not work properly. I writes to banggood service. I think that problem is not only ours. I can not add any comments....

Submit

Anna Liz can u fix this problem?

Submit

Anna Liz lo pudiste arreglar,

Submit

Dabad I hope this helps you.
when I hook up reverse cameras, I only use one power source, reverse light power, tap into positive and negative of reverse light. do not use any other method.
ignore the confusing picture that banggood put up.
it only needs reverse light power to power the camera, which also triggers the unit to auto switch to reverse camera, should do anyways.
obviously you have the unit working, just make sure you plug the camera extension cable into the "reverse camera" av input.
if this does not solve your problem either the camera or the unit is faulty.
check and double check your wiring.
if your reverse camera has lights, you should be able to see them turn on when you put your car into reverse even when it's not running, as long as ignition is on. that's the most basic way to check if you've wired it up correctly.
ideally you check with multimeter or your cars wiring diagrams as to which is pos+ and which is neg-
good luck, apologies for long message.

Submit

Exiumind maybe the camera is another video format? like ntsc/secam

Submit

Clebinho Ihave this problem, you managed to solve?

Submit

dariods youtried pal/ntsc?

Submit

Marekzenio Doesanyone has got properly working camera?

Submit

dharmakkan this problem may be due to fault camera cable . otherwise you didn't fix the connector properly. Try with another camera and wire to solve the problem.
thanks.

Submit

Sectec to make it look good you must go to factory settings, put the code 8888 and then go to the video resolution settings and place it in sd quality sd

Submit

Sectec to make it look good you must go to factory settings, put the code 8888 and then go to the video resolution settings and place it in sd quality sd

Submit

darkeyescan tamamında aynı sıkıntı var galiba 2 tane aldım bu şekilde gösteriyor ikisi de

Submit

BG141164224 I'm having the same problem i wonder if you could solve it or not.

Submit

Clebinho reversevideo resolution setting/SD

Submit

Clebinho reversevideo resolution SD

Submit

Sectec fkf

Submit

batuhanokur54 Forthose who have problems with the return camera of the product, edit the product's settings menu-fabricated settings. The rear view camera has AHD HD and SD modes, you get it in SD mode you can write in english which has image format. The problem is correcting. no interference. You have to do it this way. (Translated by Google translation. Minor spelling errors.)

0F0Kp

Submit

batuhanokur54 thosewho have problems with the return camera. edit the product's settings menu fab factory settings. The rear view camera has AHD HD and SD modes, you get it in SD mode you can write in english which has image format. The problem is correcting. no interference. You have to do it this way. (Translated by Google translation. Minor spelling errors.)

Submit

BG141164224 i m having the same problem

Submit

Mark Ibarra ibought the same car head unit and mine does the exact same i dont know what it could be

Submit

BDProductions did you hook up the wire that goes along with the video extension cable between the reverse light wire @ the tail light and the reverse trigger input on the stereo? that usually works perfect.

Submit

NikosKam Same problem. Did you find out any solution?

Submit

Mark Ibarra Ihave fixed the issue with the camera, all you need to do is go to settings then factory settings enter the code 8888 then go to protocol settings go to camera resolution settings and change it to SD and it will work, mine looked exactly like the one in your picture and i fixed it by doing that good luck!

Submit

Flyoz Checkthat the red "Trigger" wire is connected to the Cars reversing light so when reverse selected 12V ve goes to it.
When in forward gears there will be no Voltage

Submit

ozcanokan From the factory settings, there is the setting in the protocol settings, then select sd from there.

Submit

Taifun Mckinsey install on back light and at the radio the red cable connect with Brown cable

Submit

sumeda weerasekara I am also facing same problem. what happens to your issue? still I am struggling with Banggood..

Submit

sumeda weerasekara tyf

Submit

Almir Souza Ihave a similar problem. Has anyone managed to solve the problem?

Submit

karagounis14 i have the same problem

Submit

bojanmx If you use live wire from reverse light there might be a problem with canbus error control, there is little amount of current which is used to check if bulbs are blown or not, so that electricity can make problem with your camera...

Submit

Almir Souza Goodafternoon friend, did you solve the problem?

Submit

Mustafa1461 Teybin camere çıkışına şase vermen lazım ki tetiği de bağlayınca düzgün çalışacaktır😉

Submit

Para resolver o problema, basta alterar a resolução da câmera para SD

Submit

ICLEIBE omeu estava assim mas consegui consertar em configura oes, basta por em SD

Submit

Carlos Infante Compreium artigo com o n FRVFGs333SR

Submit

Mauro Marchetta CIAOBUONGIORNO NON HO ANCORA MONTATO LO STEREO, NON APPENA DOVESSI PROVVEDERE VI RENDERO NOTA
SALUTI

Submit

VANDERLEI1979 @Sectec blz irmão... vc salvou minha vida e minha câmera de ré.... deu certinho..... configurações de fabrica , 8888 , reverse vídeo resolution setting, e SD.... perfect..... muito obrigado.... abraços

Submit

VANDERLEI1979 problema resolvido.... é só ir em CONFIGURAÇÕES DE FÁBRICA....8888... PROTOCOL PARA METER SERTINGS.....REVERSE VIDEO RESOLUTION SETTING.....e colocar em SD.....

Submit

kenanc nohd
select SD

Submit

kenanc selectSD

Submit

nomdo Inthe menu 'Reverse video resolution setting' there is no SD option, only NTSC/PAL (Puqing supports fast reversing, HD does not support), AHD/25, AHD/30, TVI/25 and TVI/30.
What can I do?

Submit

pauloroso5 tem ligar um rele

Submit

Štefan Ďaďo St musíš napojiť kameru aj na žiarovku cúvacieho svetly na aute

Submit

sc0ubid0u @nomdo moi aussi je n'ai que ces options : NTSC / PAL (Puqing supports arri re rapide, HD ne prend pas en charge), AHD / 25, AHD / 30, TVI / 25 et TVI / 30.

Submit

Scarpedico in the siitings need to change the screen resolution to SD

Submit

Kobie Same problem, but mine work sometimes. Seems like there is a synchronization problem.

Submit

davutmutlu51 How can we turn off the device completely, a code was being entered, but I forgot

Submit

Kobie Got the problem solved with another camera. Seems like the supplied camera overheat as it is epoxy potted, and that is why mine work for a few seconds and then take a dive.

Submit

LLIMA You need to set the reverse camera to SD under factory settings.

Submit

BG111092117 Reversingcamera does not work, there is no sd mode in settings menu, only hd/non hd. Waste of money, camera workd with other display.

Submit

Cedrick install a relay on your 12v power supply. it will solve your problem

Submit

BG111092117 Everyinformation tells trigger wire is pink, but trigger for back up camera is BROWN, third wire from corner, black, red, brown. It takes about 0.5 seconds to camera start so if you test too fast like i did it will not show anything.

Submit

BanicaEmil Some devices cannot play AHD only CVBS, so if that reversing camera is AHD (from 720p up) the image cannot be played.

Submit