All Messages

georget This is a question for Banggood customer service. Click on Help > Contact Us at the top of the page.

2020-11-27 07:01:04 Helpful (0)
Submit
Answers (2)

Q: Does this support 32650 size battery, and is the battery removable?

Asked by pankajpathaq on 2019-09-24 02:24:25

georget No. A 32650 is too fat for the flashlight. The battery is removable so you can replace it with a higher mAh if needed.

2020-11-27 06:55:18 Helpful (0)
Submit
Answers (2)

georget Here is a link to a manual that is very close to this GM328A tester... https://img.banggood.com/file/products/20170621041627Transistor%20Tester-user-manual.pdf You will need to connect an external IR Infrared Receiver to the tester to receive codes. Something like this... https://usa.banggood.com/10pcs-Universal-IR-Infrared-Receiver-Head-With-Iron-Shell-TL1838-VS1838B-1838-38Khz-p-1211280.html?rmmds=buy&cur_warehouse=CN

2020-11-21 08:15:13 Helpful (2)
Submit
Answers (2)

Q: is keyboard.h library available in this version?

Asked by Saurav Modak on 2018-11-15 06:35:24

georget I do not see any info for keyboard.h library compiling on the D1 R2.

2020-11-20 07:32:46 Helpful (0)
Submit
Answers (2)

Q: ele vem desmontado?

Asked by Danilo Bellato Beissman on 2019-05-11 12:48:26

georget It is a kit where you have to solder the electronic components on the board and assemble the case.

2020-11-20 06:55:30 Helpful (0)
Submit
Answers (4)

georget No this is NOT an intelligent controller. It is simply an amplifier. You connect the output of your LED controller such as an Arduino, to the input of this amplifier. Then connect the output of this amplifier to a string of RGB or RGBW leds to drive them.

2020-11-20 06:51:01 Helpful (0)
Submit
Answers (1)

Q: What version firmware does the tester ship with? Is it V2.68?

Asked by georget on 2020-02-29 12:01:55

Eugen NO, mine was LCR transistor tester by efan & haoqixin v2.07, one year old now.

2020-03-01 01:45:59 Helpful (1)
Submit
Answers (3)

georget I would use the holder that comes with the Ksger soldering station. This way you can position it where ever it is most comfortable to reach. I just use the Daniu for holding the component and the magnifier to get a better view. You may still need glasses depending on how bad your eyes are.

2020-11-12 07:07:37 Helpful (0)
Submit
Answers (1)

georget Absolutely NOT 5mm. That must be a typo on the website. Always go by what the manufacture printed on the tool. 1 mm copper max. This is a precision tool for cutting component leads flush with the circuit board. Great tool for what it does.

2020-11-12 06:56:50 Helpful (0)
Submit
Answers (6)

Q: is this good also for making cutting holes in masonry walls?

Asked by Cesar Cruz on 2019-11-25 11:10:05

georget These blades are great for wood and maybe drywall, but not cement.

2020-11-12 06:46:23 Helpful (0)
Submit
Answers (2)

Q: when will stock came??available thanks

Asked by BG141016411 on 2020-11-10 06:40:55

georget It looks like it is in stock now as of 11-10-2020

2020-11-10 06:48:05 Helpful (0)
Submit
Answers (1)

georget After the battery has gone through the Pulse Repair mode and displays OFF, you should switch it over to Vehicle or Motorcycle mode if you are going to keep the charger on the battery for an extended period of time. The charger will act as a trickle charger to maintain the battery. Normally you will use the charger in Vehicle or Motorcycle mode to charge your battery. I usually use Motorcycle mode because it charges at a lower Amp. I only put the charger on my batteries in Pulse repair mode once a month.

2020-11-10 05:36:20 Helpful (1)
Submit
Answers (2)

georget Power Select 1 is the option to use if your power supply output is two wires. Power Select 2 is the option to use if your power supply has a plug or jack connected. Both options are connected in parallel on the circuit board. It is there for your convenience.

2020-11-04 09:55:44 Helpful (0)
Submit
Answers (2)

georget Yes, The charger should be able to charge EFB (Enhanced Flooded Battery) and AGM (absorbent glass mat) batteries. It is best to charge a battery slow using the Motorcycle mode of the charger. Current is limited to 1.5 amps. It may take several hours to charge depending on the state of discharge of your battery.

2020-11-04 08:52:16 Helpful (0)
Submit
Answers (3)

Q: How can I contact the seller?

Asked by MikeDAWolf on 2019-04-24 07:45:51

georget At the top of the page, click Help.

2020-11-04 08:42:21 Helpful (0)
Submit
Answers (2)

Q: does it work with usb? or what plug does it use?

Asked by Pulsh on 2017-12-11 10:28:02

georget No, USB does not supply enough power. The LED strip requires 12v and around 6 Amp. Get a power supply something like this... https://www.banggood.com/AC-100-240V-to-DC-12V-5A-60W-Power-Supply-Adapter-For-LED-Strip-Light-p-994870.html

2020-10-27 11:14:48 Helpful (0)
Submit
Answers (5)

Q: which specific power supply I need to buy? measures

Asked by BG131612938 on 2020-10-25 10:07:46

georget This one is 5A which is a little low but should be ok. It has the correct size connector 5.5mm x 2.1mm https://www.banggood.com/AC-100-240V-to-DC-12V-5A-60W-Power-Supply-Adapter-For-LED-Strip-Light-p-994870.html

2020-10-27 11:12:48 Helpful (0)
Submit
Answers (1)

Q: does it works with an 5.5mmX2.1mm power supply with 12V and 2A?

Asked by BG131612938 on 2020-10-25 11:06:29

georget 2A is too low. You should power the strip with at least 6A. When the strip displays white, it will draw the most power.

2020-10-27 10:57:09 Helpful (0)
Submit
Answers (1)