Unfortunately, the package arrived with a very poor packaging, in an envelope too improvised to contain delicate items that have to face such a long journey. Being delicate components and accessories for a 3D printer I think they should be better protected. I hope that when I mount them on the printer there are no missing parts and that everything works well.

Purtroppo il pacco è arrivato con un imballo molto scadente, in una busta troppo improvvisata per contenere degli articoli delicati che devono affrontare un viaggio così lungo. Essendo componenti delicati ed accessori per una stampante 3D credo che dovrebbero essere meglio protetti. Spero che quando li monterò sulla stampante non manchino parti e che tutto funzioni bene.

Unfortunately, the package arrived with a very poor packaging, in an envelope too improvised to contain delicate items that have to face such a long journey. Being delicate components and accessories for a 3D printer I think they should be better protected. I hope that when I mount them on the printer there are no missing parts and that everything works well.

Well made extruder. A nice addition to my Ender 3 V2. I recommend this to make sure the filament is properly pushed to the nozzle. Packaging can be better.

Well made extruder. A nice addition to my Ender 3 V2. I recommend this to make sure the filament is properly pushed to the nozzle. Packaging can be better.

Well made extruder. A nice addition to my Ender 3 V2. I recommend this to make sure the filament is properly pushed to the nozzle. Packaging can be better.

Igényes, sorjamentes kidolgozás, minden alaktrész a csomagban van. Nem mellesleg jól is néz ki a nyomtató vele. :D

Igényes, sorjamentes kidolgozás, minden alaktrész a csomagban van. Nem mellesleg jól is néz ki a nyomtató vele. :D

Igényes, sorjamentes kidolgozás, minden alaktrész a csomagban van. Nem mellesleg jól is néz ki a nyomtató vele. :D

As described. Installed on Anycubic i3 Mega S and getting rid of the factory plastic Titan extruder (replica). after installation, e-steps calibration is needed to tune your 3d printer properly. Printing quality improved, minimize under extrusion issues and noise. i totally recommend this extruder!!

As described. Installed on Anycubic i3 Mega S and getting rid of the factory plastic Titan extruder (replica). after installation, e-steps calibration is needed to tune your 3d printer properly. Printing quality improved, minimize under extrusion issues and noise. i totally recommend this extruder!!

As described. Installed on Anycubic i3 Mega S and getting rid of the factory plastic Titan extruder (replica). after installation, e-steps calibration is needed to tune your 3d printer properly. Printing quality improved, minimize under extrusion issues and noise. i totally recommend this extruder!!

just getting around to reviewing this, because I just had to use it. my stock extruder failed and I had to finally use it. works so much better than my stock extruder!

just getting around to reviewing this, because I just had to use it. my stock extruder failed and I had to finally use it. works so much better than my stock extruder!

just getting around to reviewing this, because I just had to use it. my stock extruder failed and I had to finally use it. works so much better than my stock extruder!

Arrived amazingly quickly (less than a week) and looks great. A similar one on another site was 4 times as much so happy with the price. Yet to install but that’ll be a fun post holiday season project

Arrived amazingly quickly (less than a week) and looks great. A similar one on another site was 4 times as much so happy with the price. Yet to install but that’ll be a fun post holiday season project

Arrived amazingly quickly (less than a week) and looks great. A similar one on another site was 4 times as much so happy with the price. Yet to install but that’ll be a fun post holiday season project

easy to install read some other comments and i also changed the e steps to 138,6 works great also some people said that the inlet was touching the z threaded bar all i did was to tighten the socket so one of the flats was next to the bar .

easy to install read some other comments and i also changed the e steps to 138,6 works great also some people said that the inlet was touching the z threaded bar all i did was to tighten the socket so one of the flats was next to the bar .

easy to install read some other comments and i also changed the e steps to 138,6 works great also some people said that the inlet was touching the z threaded bar all i did was to tighten the socket so one of the flats was next to the bar .

All perfect so far! Haven't installed it yet.

All perfect so far! Haven't installed it yet.

All perfect so far! Haven't installed it yet.

Filament can be pushed inside only if you unscrew the coupler for the PTFE tube. So not so easy if you change a lot the filament. Running tests now after I did the E steps calibration.

Filament can be pushed inside only if you unscrew the coupler for the PTFE tube. So not so easy if you change a lot the filament. Running tests now after I did the E steps calibration.

Filament can be pushed inside only if you unscrew the coupler for the PTFE tube. So not so easy if you change a lot the filament. Running tests now after I did the E steps calibration.

ótimo produto, excelente qualidade

ótimo produto, excelente qualidade

ótimo produto, excelente qualidade