Customer Reviews

4.92 out of 5
See all 334 reviews
Write a Review
  • All Reviews (334)
  • Image (30)
  • Video (0)
  • All Star
    • All Star(334)
    • 5 Star(317)
    • 4 Star(10)
    • 3 Star(4)
    • 2 Star(2)
    • 1 Star(1)
Sort by:
Top Review
  • Top Review
  • Most Helpful
  • Most Recent
Reviews only from your country (United States)
Show Original

A part of the review has been auto-translated.

  • 24/09/2014

    Works well, very compact adapter. I put up a picture showing how you can modify the board to work with Arduino. Just cut the trace going from the chip to the R3 resistor, then solder a tiny wire from the chips' top left pin (pin 28) to the RST pin.

    Show Original
  • 26/01/2014

    Drivers available: I didn't need to install driver for openSUSE 12.3 (3.7.10 kernel). As usual, a tiny bit of documentation would be comforting. Using the supplied jumper between RXC and TXC, loopback works. Remove jumper. Connect GND (blk) to GND, RXC (wht) to RXD, TXC (gry) to TXD, 5V (vio) to VCC. (RST (blu) to RESET?)

    Show Original
  • 07/03/2017

    Получил устройство за 21 день. Драйвер автоматически установился быстро на Win/ 7 (64). Все работает. я доволен. Рекомендую.

    Show Original
  • 30/12/2016

    There isn't DTR contact. Because of this you can not flash micro minimOSD (I think other osd plates too)

    Comments (2)
    Show Original
  • 14/06/2016

    мне понравилось, визуально... Когда заказывал было дикое желание и необходимость, а сейчас даже не помню что хотел. :) Вот так это выглядит)

    Show Original
  • 29/03/2017

    need this absolutely but still waiting for since November 2016, resent by BG in March

    Show Original
  • 10/04/2020

    The parcel was delivered quickly, it arrived within a month. Looks like it works, but I'll check it out.

    Show Original
  • 06/02/2020

    It works!

    Show Original
  • 31/10/2019

    Buon convertitore USB TTL, realizzato discretamente ed isolato con guaina termorestringente trasparente. Ha tre LED sul pcb che conferma la sua alimentazione e di funzionamento. La scocca del connettore USB non è ben saldato al pcb, si consiglia di saldarlo al pcb per evitare rotture in fase di inserimento o estrazione da/verso porta USB, comunque io ho ripassato tutte le saldature del connettore USB. Compresi 4 cavetti da 12 cm per il collegamento. Consigliato per programmazione ESP8266.

    Show Original
  • 25/11/2018

    المنتج وصل بصوره جيده ومغلف بطريقه جيده وصل خلال ٢١ يوم وهو وقت مناسب جدا

    Show Original

    Total 0 pages

    Go to page

    recommendation for you
    • US$0.99
    • US$41.99
    • US$169.00
    • US$33.99
    • US$104.99
    • US$36.00
    • US$100.00
    • US$13.73
    • US$17.99
    • US$12.99
    • US$78.99
    • US$116.00
    • US$85.00
    • US$103.34
    • US$53.99
    • US$79.79
    • US$43.99
    • US$11.99