Customer Reviews

4.89 out of 5
See all 131 reviews
Write a Review
  • All Reviews (131)
  • Image (13)
  • Video (1)
  • All Star
    • All Star(131)
    • 5 Star(122)
    • 4 Star(7)
    • 3 Star(0)
    • 2 Star(0)
    • 1 Star(2)
Sort by:
Top Review
  • Top Review
  • Most Helpful
  • Most Recent
Reviews only from your country (United States)
Show Original

A part of the review has been auto-translated.

  • 09/02/2020

    The board I ordered was supposed to be the Version 1 board, but they sent the same version 2 board that does not work with the Laser as advertised. This is the last straw everytime I buy buy from Banggood I am dissappointed with their quality, build instructions and/or usability of their products. Not happy

    Show Original
  • 06/09/2021

    This is the seventh cnc board I received from Banggood. This one worked without any problems, but 4 of the 7 boards had some kind of a problem. The stepper motors would just stop working without any warning, but the spindle keeps running! Then you have to turn off the power of the machine and restart all over again. Also, some of the boards did this on their own, but some would do it when being lightly touched, by literally anything. I solved the problem on two boards by replacing the stepper drivers, but on others that didn't do the trick. I even tried resoldering the whole board, but to no avail. The 3018 CNC is a great little machine, but after dealing with 7 of them and facing control board problems, I honestly feel like these boards are the weakest part of the machine and should be made to a higher quality standard.

    Comments (1)
    Show Original
  • 11/03/2021

    Well packed. Din't test it yet, but should work just fine.

    Show Original
  • 05/12/2019

    all parts are in the package, it came in a different color than on the product page and a few components were crooked soldered. never the less hood product.

    Comments (2)
    Show Original
  • 19/10/2019

    Grandioso implemento de electrónica para mejorar la calidad de mis proyectos

    Show Original
  • 03/09/2020

    This engraver controller works very good had no issues with it I might buy another one in the future What I like about it is that you can run a spindle motor either with the power output jack or you can use a speed controller just by moving the jumper Once you have moved the jump could used a laser controller in this position One note which is a minor complaint and that is where the jumper is it should be marked a little bit better I have a work around and that is remove the connector or use a cooling fan connector and wire it to a switch and mark the switch case also there two green LED lights that light up the top one is when you have the jumper in the power supply jack the second LED light is red and this is the power supply light the third LED light is green also and this one is PWM output or TTL output light One other note the TTL output to me does not seem to work as good as the PWM setting now this could be the laser controller problem the spindle motor controller I have not been able to get it work correctly on either setting yet but it might operator error

    Show Original
  • 07/09/2021

    My best boss

    Show Original
  • 05/10/2020

    I haven't tested the board yet, the processing is good.

    Show Original
  • 18/09/2020

    Nice replacement CNC Controller for the 3018 Router.

    Comments (3)
    Show Original
  • 17/02/2020

    Great product

    Show Original

    Total 0 pages

    Go to page


    You might be interested in

    recommendation for you
    • US$149.99
    • US$85.99
    • US$35.94
    • US$14.99
    • US$9.99
    • US$10.99
    • US$9.20
    • US$12.99
    • US$7.99
    • US$16.81
    • US$69.99
    • US$67.99
    • US$51.99
    • US$13.99
    • US$16.49
    • US$119.99
    • US$99.99
    • US$20.31