Excellent small job stripping machine. BE CAREFULL the knives are SHARP. The knives punctured the plastic bag and fell out onto the counter when I opened the box. Construction is excellent. I am looking forward to using this tool often. I can highly recommend this manual machine for light use. If you are needing high production, a powered machine might be a better option. This one appears to be well built. Thank You Banggood for another great tool at a reasonable price.

Excellent small job stripping machine. BE CAREFULL the knives are SHARP. The knives punctured the plastic bag and fell out onto the counter when I opened the box. Construction is excellent. I am looking forward to using this tool often. I can highly recommend this manual machine for light use. If you are needing high production, a powered machine might be a better option. This one appears to be well built. Thank You Banggood for another great tool at a reasonable price.

Excellent small job stripping machine. BE CAREFULL the knives are SHARP. The knives punctured the plastic bag and fell out onto the counter when I opened the box. Construction is excellent. I am looking forward to using this tool often. I can highly recommend this manual machine for light use. If you are needing high production, a powered machine might be a better option. This one appears to be well built. Thank You Banggood for another great tool at a reasonable price.

Ok goog

Ok goog

Ok goog

fantastic well made item

fantastic well made item

fantastic well made item

for thick wires fine, for little ones a bit more difficult

voor dikke draden prima, voor kleintjes wat moeilijker

for thick wires fine, for little ones a bit more difficult

Very good!

Muito bom!

Very good!

works really well.found easier to pull manually through rather then use a drill. it broke the blade the first time I tried the drill

works really well.found easier to pull manually through rather then use a drill. it broke the blade the first time I tried the drill

works really well.found easier to pull manually through rather then use a drill. it broke the blade the first time I tried the drill

Really hard to use as it is. The screwdriver loosens constantly and the structure deforms easily (metal too thin). The adjustment of the knives is very delicate and the clamping butterflies do not hold them well in place. To be replaced by BTR screws with shoulder tip. The knives are not well sharpened (they are asymmetrical) and therefore cut through. After a certain length of wire, the blade deforms and breaks. The original sharpening cannot be obtained by hand but you can get close to it and get a better cut! I do not recommend making a flat to press the locking screw to keep all the alignment adjustment latitude. The adjustment is therefore difficult, so it is better to make sure that all the identical yarns have been prepared and processed in a single batch. The wires should be straightened as well as possible, the system does not like folds. Once the sheath is cracked, the peeling is really easy, it's worth spending time improving the device. Tried in manual traction only, I did not dare to motorize the device so as not to break the tools.

Vraiment difficile à utiliser en l'état. La visserie se desserre constamment et la structure se déforme facilement (métal trop fin). Le réglage des couteaux est très délicat et les papillons de serrage ne les maintiennent pas bien en place. A remplacer par des vis BTR à bout épaulé. Les couteaux ne sont pas bien affûtés (ils sont asymétriques) et coupent donc de travers. Au bout d'une certaine longueur de fil, la lame se déforme et casse. L'affûtage d'origine ne peut pas être obtenu à la main mais on peut s'en approcher et obtenir une meilleure coupe ! Je ne recommande pas de faire un plat pour appuyer la vis de blocage pour garder toute la latitude de réglage d'alignement. Le réglage étant donc pénible, il vaut mieux s'assurer d'avoir préparé tous les fils identiques pour les traiter en un seul lot. Les fils doivent être redressés le mieux possible, le système n'aime pas les pliures. Une fois que la gaine est fendue, l'épluchage est vraiment facilité, ça vaut le coup de passer du temps à améliorer le dispositif. Essayé en traction manuelle uniquement, je n'ai pas osé motoriser l'appareil pour ne pas casser les outils.

Really hard to use as it is. The screwdriver loosens constantly and the structure deforms easily (metal too thin). The adjustment of the knives is very delicate and the clamping butterflies do not hold them well in place. To be replaced by BTR screws with shoulder tip. The knives are not well sharpened (they are asymmetrical) and therefore cut through. After a certain length of wire, the blade deforms and breaks. The original sharpening cannot be obtained by hand but you can get close to it and get a better cut! I do not recommend making a flat to press the locking screw to keep all the alignment adjustment latitude. The adjustment is therefore difficult, so it is better to make sure that all the identical yarns have been prepared and processed in a single batch. The wires should be straightened as well as possible, the system does not like folds. Once the sheath is cracked, the peeling is really easy, it's worth spending time improving the device. Tried in manual traction only, I did not dare to motorize the device so as not to break the tools.